OLV INTERNACIONAL

2000 HP VFD DRILLING PACKAGE
A/C DRAWWORKS: API-7 .
2,000 HP, Grooved for 1-1/2” wire line, (2) Motors :A/C 1050 hp with 230/460 Volts, 10 HP Blower Motor
Auxiliary brake Eaton air water cooled disc.
MAST AND SUBSTRUCTURE; API 4F &Q .
One (1) Cantilever Lo-Lift Beam Leg Drilling Mast with a minimum clear height of 147’-0” x 30’-0” wide base and a rated static hook load of 1,000,000# on twelve (12) lines strung to the traveling block per API 4E-4F Q1 Specifications. Mast is designed for 100 mph wind load with a full rack of pipe and 115 mph on a bare mast. In addition, the mast has a 1,000,000 lbs. casing capacity simultaneous with 800,000 lbs. setback capacity. Mast stem portal truss are designed affording excellent driller’s view and is complete with raising sheaves, A-frames, and sling lines.(OPTIONAL) Sling lines remain in back face of mast when not in use. Mast will accommodate a 35’-0” high drill floor and has full height straight ladder, from drill floor to crown. The mast will be provided with pad eyes for fixation of an intermediate tubing stabbing board at an intermediate level. (Intermediate Tubing Stabbing Board included.)
One (1) Hydraulic Snubbing System installed in A-frames allows driller to have full control of break-over during raising and lowering operations of mast.

One (1) 600-Ton (12 Line) Crown Block with six (6) 60” minimum diameter cluster sheaves and a 60” minimum diameter fast line assembly, all with tapered roller bearings and grooved for 1-3/4” diameter wireline. Cluster assembly is mounted on a crown frame which includes line guards, oak bumper blocks with expanded metal safety screen and pad eyes to accommodate two (2) 6-ton cat line sheaves, one (1) ten-ton core line sheave, one (1) for hanging the traveling block and one (1) for hanging air hoist. Crown safety platform for crown service with 3’-6” high handrails, checkered plate flooring and safety gate at ladder opening is included. Each sheave is lubricated by individual grease channels and zerks located on one end of the shaft. Complete with one (1) 12,000 lbs. capacity rotating jib crane. Block and tackle included.

One (1) Heavy Duty Racking Platform with a capacity for 240 stands of 5”in. drill pipe and 10 stands of 8” to 9-1/2” drill collars. Platform is complete with folding diving board, access catwalk and fold-up floor slab for driller’s side. Platform is adjustable from 77’-0” to 87’-0” above drill floor. Handrails are 7’-0” high constructed of 2” square tubing with toe plates. Also includes a bracket at the platform with
one (1) new Ingersoll Rand model BU7A or equal air winch for pulling back drill collars, complete with safety chains.



One (1) Belly Board complete with handrails and toe boards.

One (1) Geronimo Derrickman Escape System including wireline, base anchor, hand brake and “T” type riding seat.

One (2) Set of Eight (8) Standpipe Clamps for dual 5” nominal diameter standpipes located on driller’s side.

Two (2) Air Hoist Sheave Unit 14” OD steel sheave grooved for 5/8” diameter wireline (or 1-1/2” manila rope) and mounted on bronze bushings. Swivel and shackle are included.

Two (2) Cat line Sheave Units 16” OD steel sheave grooved for 5/8” diameter wireline (or 1-1/2” manila rope) and mounted on bronze bushings. Swivel and shackle are included.

One (1) Coreline Sheave Unit 24” OD steel sheave grooved for 9/16” diameter wireline and mounted on roller bearings. Swivel and shackle are included.

One (1) Set of Leveling Equipment for leveling all four points of mast at floor elevation using hand pump, including one (1) 100-ton jack, 2” thick shim packs for each leg, and extra long A325 bolts. (Only one jack required).

Two (2) Tong Counterweights each having a capacity of two (2) tons and complete with water buckets, guide tracks, 8” snatch blocks, and wire line with swedge sockets.

Two (2) Cat line Booms 20’-0” long with 5,000# capacity each installed on both sides of mast, complete and including sheaves grooved for 5/8” line, safety latches and all necessary support and lift lines.

One (1) Mast Stand 12’-3: high to support crown while pinning racking board including oak block headrest.

Two (2) Mast Assembly Stands 6’-0” high to support mast bottom during assembly.

Support Material to mount deadline anchor in mast bottom section. (Dead line anchor to be furnished.

One (1) Universal Casing Stabbing Board is adjustable from 20’-0” above drill floor to 50’-0” above drill floor and is complete with access ladder and one (1) 1000 lbs. air powered hoist with controls and attachment brackets. The air hoist is equipped with over-speed sensor, load brake and damage cable sensor, two (2) additional safety locks with speed sensors are provided independent of the main load brake. At an elevation above the stabbing board a derrick man harness, with shoulder straps and safety
line attachment pad eyes, will be provided. This stabbing board will be designed, fabricated and teste